Cisco smart serial connections are used and utilized by the Hwic-1t, Hwic-2t, Hwic-2t, and Hwic-2a/s. Table 3 contains a list of the cables that are supported. There is a rj-45 connection used by the hwic-1dsu-t1. An eia/tia-232, eia/tia-449, v.35, x.21, data terminal equipment/data communications equipment (dte/dce) interface, eia-530 dte interface, or nonreturn to zero/nonreturn to zero inverted (nrz/nrzi) serial interface can be provided to a Cisco modular router by the 1-port serial hwic (hwic-1t), which is depicted in figure 1. The 2-port serial hwic (hwic-2t), which is depicted in figure 2, is shown in figure 2. router#show version 1 virtual private network (vpn) module 1 cellular interface dram configuration is 64 bits wide with parity enabled. This configuration is used by the router. There are 479 thousand bytes of nvram. router#show the product (fru) number is hwic-3g-gsm, and the version identifier is na. diag wic slot 0: 3g wwan hwic-hsdpa/umts/edge/gprs-850/900/1800/1900/2100mhz… shutdown of the router with the command router#show run! interface cellular0/0/0 reboot In order to offer extremely flexible connections for Cisco 1800, 1900, 2800, 2900, 3800, and 3900 series integrated services routers, high-speed WAN interface cards (hwics) that allow for serial and asynchronous communication are used. Customers are able to deploy many applications with the use of these hwics, including dial access server, console server, legacy protocol transfer, and WAN access. When it comes to typical networking issues, such as remote network administration, external dial-modem access, low-density WAN aggregation, legacy protocol transfer, and high-port-density support, you have the ability to mix and combine hwics in order to design cost-effective solutions. Please visit this link for further information on Cisco. The hwic-1t is a serial WAN interface device with one port. Cisco Smart Serial connections are used by the hwic-1t, hwic-1t, hwic-2t, and hwic-2a/s wireless interface controllers. Table 3 contains a list of the cables that are supported. There is a rj-45 connection used by the hwic-1dsu-t1. An eia/tia-232, eia/tia-449, v.35, x.21, data terminal equipment/data communications equipment (dte/dce) interface, eia-530 dte interface, or nonreturn to zero/nonreturn to zero inverted (nrz/nrzi) serial interface can be provided to a Cisco modular router by the 1-port serial hwic (hwic-1t), which is depicted in figure 1. The 2-port serial hwic (hwic-2t), which is depicted in figure 2, is shown in figure 2. router#show version 1 virtual private network (vpn) module 1 cellular interface dram configuration is 64 bits wide with parity enabled. This configuration is used by the router. There are 479 thousand bytes of nvram. hwic-hsdpa/umts/edge/gprs-850/900/1800/1900/2100mhz… product (fru) number: hwic-3g-gsm version identifier: na router#show diag wic slot 0: 3g wwan iprs-850/900/1800/1900/2100mhz shutdown of the router with the command router#show run! interface cellular0/0/0 reboot In order to offer extremely flexible connections for Cisco 1800, 1900, 2800, 2900, 3800, and 3900 series integrated services routers, high-speed WAN interface cards (hwics) that allow for serial and asynchronous communication are used. Customers are able to deploy many applications with the use of these hwics, including dial access server, console server, legacy protocol transfer, and WAN access. When it comes to typical networking issues, such as remote network administration, external dial-modem access, low-density WAN aggregation, legacy protocol transfer, and high-port-density support, you have the ability to mix and combine hwics in order to design cost-effective solutions. Please go here for further information on Cisco.
I love myBlogd
Author
jackemails@gmail.com